N 6566 is a pocket door guide for 1-3/8 in thick doors. It is a universal fit used by many pocket door manufacturers. Made of stamped steel with nylon guide tips, it mounts onto the bottom of the pocket door opening and under the trim. It keeps the door from hitting side to side as it slides back and forth.

N 7015 is a set of left and right hand nylon pocket door guides that can be used for any thickness door. It is a universal fit used by many pocket door manufacturers that is screwed onto the jamb under the trim. It has slotted holes for adjustment in or out. It keeps the door from hitting side to side as it slides back and forth.

This guide uses slotted mounting holes to adjust a pocket door horizontally. Can be used with any door thickness. Lighter weight for hollow core doors. Sold in pairs.

Johnson Hardware Door Edge Pull, Plate Size: 0.09 in, 0.62 in W, 2.94 in H, Aluminum, US3 Brass, Suitable for: 1-3/8 to 1-3/4 in Thick Doors

Use for 1-3/4 in Thick doors.

Use for joining two Johnson pocket door frames.

N 7410 is a four wheeled pocket door roller assembly used on a double track that has a 1-5/8 in inside width with a 1-3/16 in center to center measurement. The four 1 in Dia nylon convex rollers provide a smooth, long-lasting, quiet operation and are affixed to an adjustable stamped steel housing that slides into a stamped steel mounting bracket. Used on a 1-3/8 in thick door and 80 lb.

N 6724 is a four roller pocket door roller assembly used on Kennaframe pocket doors and others. The four 23/32 in Dia nylon rollers are affixed to an adjustable spring loaded steel bracket. They ride in a double track mounted in the top of the pocket door opening. It has a dial-adjust wheel that makes it adjustable up to 3/8 in height. It can be used on pocket doors 1 in to 1-3/4 in thick and up to 100 lb. each.

Size of 3-7/8 in x 3/4 in x 1-5/8 in. Slim pak, polybagged.

Heavy-duty hangers with 3 ball bearing equipped wheels for long, trouble free service - never needs lubrication. Height adjustable. 200 lb weight capacity. 1 x 3 in plate size.

Hardware kit for 1500 Series pocket door frames includes #1120 hanger, #1513 bumper, #1550 guide, #1712 adjustment wrench and screws.

National Hardware Pocket Door Hardware Kit, Plastic/Steel, Includes: (1) Bumper, (2) Floor Brackets, (2) Guides, (2) Mounting Plates, (2) Wall Brackets, (2) Wheel/Bracket Assemblies and All Nails and Screws Necessary For Assembly

A fast, convenient method of finishing a pocket door installation. Just cut to length and install. No ripping of special thickness stock. Presanded so finishing is a snap.

A versatile single track system, the 100PD designed and packed primarily for "on-the-job" construction of pocket doors, but also usable in combination with itself or other Johnson Series tracks for special installations of sliding doors. Aluminum track with convex rails, jump-proof three-wheel hangers. Heavy-gauge steel components are zinc-plated for a quality appearance. Components are available in bulk for fabricators, as are fixtures for assembly of pocket door frames.

National Hardware Pocket Door Hardware, Door Thickness: 3/4 to 1-3/4 in, Aluminum/Particle Board/Steel, Includes: (1) Header and Track Assembly, (4) Jamb Stiffeners, (2) Floor Brackets, (1) Door Guide Set, (2) Snap-in Door Plates, (2) Snap-in Hangers, (1) Bumper, (1) Wrench

The 1500 Series standard-duty pocket door frame is designed to carry heavy standard size doors (up to 125 lb each) in standard 2 x 4 timber or steel framed stud walls. The 1500 frame kit is packaged for easy transport and fast installation for either single door or converging door applications. The 1500 is a versatile frame and can be adapted for use in non-standard wall thicknesses, block masonry walls and can be cut down to accept any smaller size door size.

The 200PD is commercial-grade hardware ideally suited for heavy door applications where smooth, trouble-free operation and long life is a necessity. The 200PD is primarily designed for on-site pocket door fabrication but can be adapted for use in other various configurations and applications. The heavy-duty extruded aluminum I-beam track is made to precise specifications and zinc-plated ball bearing wheel hangers are manufactured with Johnson's assurance in mind. Heavy-gauge steel components are zinc-plated for a quality appearance.

The 1500HD Series pocket door frame is designed to carry heavy solid core doors weighing up to 200 lb Ball bearing hanger wheels provide feather-touch door operation making the 1500HD one of the smoothest rolling pocket door installations available. The 1500 is designed to be quickly installed into prepared 2 x 4 timber frame stud walls however, the 1500 can also be adapted for use in various wall thicknesses and with various wall materials and structures. The 1500 frame kit is packaged for easy transport and fast installation for either single or converging 2 door applications and all frame sizes can be cut down to accommodate custom size doors.