Smooth unlocking motion of a burr free hook. Durable one piece spring steel construction is virtually indestructible. Blade is angled from the bottom plane of the handle. Easy to grasp non-slip textured handle grip with a 1/4" handy oversize hang hole in handle. Length: 6-1/4".
Manufactured of tough, long-lasting, weather-resistant nylon material. Use the facing gauge while working across the width of the plank for greater accuracy of the desired exposure and guards against sagging. The facing gauge may also be used in combination with the Malco Overlap Gauge [SKU#119.9975] to prop up one end of the plank for one-person application. Adjustable for precise 5", 6", 7" or 8" exposures.
Drive trim nails into soffit, fascia and other finishing trim without denting or marring material. All steel nose and aluminum tail piece directs weight of this punch to the working end when grasping or starting a nail. Accommodates up to 1-1/4" (31.2 mm) standard trim nails.
Add snap lock plastic skirting and siding to finishing trim. Makes tabs in the cut edge of siding panel. Used as a finishing course at top of wall or below window. Tabs lock into utility trim. Punch raises a high projection to compensate for natural relaxation of vinyl plastic. It also works well on aluminum siding but is not recommended for steel. NOTE: Should not be used when PERMATABS are required to snap into finished trim. Throat depth is 3/8"; length is 9".
Strong, one-piece tempered spring steel construction with precision-ground tip assures gauge will grip behind siding plank. No adjustments to vary and nothing to mark. Will not mar finish of pre-painted siding. Works with 5/16" (7.9 mm) fiber cement siding. Permits 1-person application of panels. Two gauges support entire length of panel and precisely gauge a standard 1-1/4 inches (31.2 mm) overlap.
Produces a double crimp that downsizes without deforming down-spout; walls stay square for a tight fitting, leakproof connection. Tool also features rust resistant plating. Ergonomic REDLINE handles with unique one hand operation latch.
For punching holes in vinyl and aluminum siding. Punches horizontal slot for adding or elongating nail holes in siding to accommodate irregular stud spacing. Slot: 5/32" x 3/4"; 5/8'' Throat Depth; Length 8-1/2". Ergonomic REDLINE handles with unique one hand operation latch.
Use for making drain tabs and notches in 5/8" J channel. Stop gauge to adjust cutting depth for various profiles. Compound leverage for smooth and easy cutting action ergonomic REDLINE handles with unique one hand operation latch. Grip is color coded for easy tool identification. Durable all steel construction, rust resistant nickel chrome and black oxide finishes prolong the life of the tool.
Strong aluminum frame with comfortable vinyl grips. Big 3-inch (76 mm) high carbon steel blades with a knife-like edge. Makes precise left or right circular cuts to 6-inch (15 cm) diameter and fast straight cuts. Cuts thick or layered vinyl and a variety of other flexible non-ferrous materials; not for use on sheet metal. Replacement blade MV12RB.
Unique one-hand operation latch; soft-touch, non-slip handle insert; ergonomically contoured handles; opening maximizes handle leverage. Throat depth adjustments: 1/4" to 5/8".
For securing vinyl skirting and siding to finishing trim. Produces wider, more secure locking tab projections. Tabs grip a greater surface area and guard against dislodging due to relaxation of vinyl from heat. Installations also resist blowout during times of high pressure and wind. Constructed of steel stampings and rugged investment cast alloy steel jaws. Nickel plate and black oxide finish with compound leverage design ergonomic REDLINE handles with unique one hand operation latch. Not Recommended for use below 32 degrees F (0 degrees C). Throat Depth 1/2"; Length 8-1/2".
Precise vee-notched depth graduations on jaws are in 1/4"(6.4 mm) increments. Jaws are drop forged, high impact steel. Hardened steel handles resist abuse. Powerful compound leverage design. Tool also features rust resistant nickel plating. Ergonomic REDLINE handles with unique one hand operation latch. Jaw width is 3-1/4"; Jaw depth is 1-1/4".
Works overhead or in confined areas. Precise vee-notched depth graduations on jaws are in 1/4"(6.4 mm) increments. Jaws are drop forged, high impact steel. Hardened steel handles resist abuse. Powerful compound leverage design. Tool also features rust resistant nickel plating. Ergonomic REDLINE handles with unique one hand operation latch. Jaw depth is 1-1/4".
Insert under siding or clapboard to ventilate walls. Eliminates moisture and peeling paint on exterior walls. Use flat blade screwdriver to insert under siding.
Produce uniform, accurate bends in sheet steel and non-ferrous metals with greater control and efficiency. Jaws are drop forged, high impact steel. Hardened steel handles resist abuse; also minimize buckling and bowing of metal. Fewer strokes are required to bend and straighten angles. Designed for all the metal trades, including HVACR installation, roofing and siding applications and commercial building and remodeling. For bends in flashing, fascia corners. Jaw width is 6"; Jaw depth is 1-1/4".
Gauges and supports siding for one-person installation with virtually no layout time; friction-cam mechanism for holding power; won't scratch or mar pre-painted siding.
Used to install primed or pre-painted cement-board siding without lines on wall; gauges and supports siding for one person installation with virtually no layout time. Tool has a friction cam mechanism for holding power, non marring design, super tough and fits easily in tool bags. One unit is a pair of two Gecko Gauges, (sold as a pair)
Blade design delivers clean, accurate cutting; dust free indoor/outdoor operation; for fiber cement products up to 5/16" thick.
Easily transport a bending brake around the jobsite; solid frame construction; lightweight and comes standard with wheels. Use with sku# 592.3602.
Quickly cut material to desired size; strong, durable case hardened steel knives. Use With: Mark I , II (sku# 592.3602) & IV Series Brakes. Applications: Galvanized Steel; Copper; Zinc: Vinyl; Aluminum Sheet; and Stainless Steel.
Portable bending brake for capping and trimming fascia, doors, windows and siding; able to hem to add strength and smooth edges to any profile; engineered for durability and reliability to provide an accurate bend every time; design for aluminum trim coil and light gauge sheet stock. For residential construction.