Noncombustible caulk designed to resist high-temperatures and smoke in non-rated construction. Blocks drafts, smoke and fire. Use around wires, pipes, ducts and vents. Resists temperatures up to 1,380 degrees Fahrenheit. Meets ASTM specifications E-136.
Designed to resist high temperatures and smoke passage in non-rated construction. Can be used with a standard caulking gun, or pneumatic pumping equipment. Easily applied with a putty knife or trowel. Fast-dry, tack-free in 15 minutes. Gray in color. Meets ASTM E - 136, 2003 IRC, 2003 IBC.
One component, general purpose fire rated sealant and smoke seal for construction joints and through-penetrations. No-sag caulking grade sealant. Cures to an elastomeric seal that is suitable where dynamic movement is expected. 10.3 ounce covers 18 cu. in.
Inorganic and has no volatile solvents which makes it particularly useful when installing in confined spaces or occupied areas. Does not have asbestos fillers. A single component system, no mixing necessary and no required additives. DOT Classification is not regulated. General purpose, residential acoustical caulk for electrical, plumbing, plastic pipe and telephone communication systems penetrations. 10.3 ounce covers approximately 18 cu. in.
Reusable nozzle. Approved fireblock penetration sealant, fills and seals service penetrations. UL tested, Class 1 foam. Meets UL 1715, UL94 V-O, ASTM 814 E -84. Tinted bright orange for easy identification.
For filling, insulating and sealing gaps, cracks and openings in buildings. Inhibits the passage of fire through residential utility penetrations. Can be used to seal against gas, smoke, and energy loss. Evaluated Per ICC-ESR-3402. Type V residential fireblock. Tested according to ASTM E 814 NFPA 286. With nozzle.
Designed for use as a one-part fire, smoke, noxious gas and water resistant sealant. Easy cleanup no special handling, routine disposal. Intumescent, Fast dry, tack-free, in 8-12 minutes. Paintable after 72 hour cure. Meets ASTM E 814 and ASTM E 1966.
Forms a tight barrier against fire, smoke and toxic fumes. Suitable for a wide variety of through-penetration fire stops, including cable, metal pipe, insulated pipe, glass pipe, construction gaps, HVAC ductwork and certain plastic pipe applications. Cures to form a flexible seal, installs with a standard caulking gun, pneumatic pumping equipment or putty knife. ASTM, FM and U.L. tested for 3 hour fire penetration seal for walls and floors.
One component, general purpose fire rated sealant and smoke seal for construction joints and through-penetrations. Extremely intumescent, non-sag caulking grade sealant. Cures to an elastomeric seal that is suitable where dynamic movement is expected. 10.3 ounce covers about 18 cu. in.
Designed for wall and floor applications in UL rated construction. Use on aluminum, pre-cast concrete gypsum, wall board, power/communication cables and aluminum/galvanized steel cable trays, static/non-static pipes and conduits, CPVC, PVC, and steel. Resists cracking. Forms pressure tight seal resistant to water, smoke and toxic gases. Withstands temperatures up to 300 degrees Fahrenheit. Can be applied at temperatures from negative 20 degrees Fahrenheit to 122 degrees Fahrenheit. Meets ASTM E-814 (UL1479) and FBC System Compatible. ASTM specifications C-920, Type S, Grade NS, Class 25.
Used for all combustible and non-combustible penetrations, excellent adhesion to unprimed surfaces.
Classified for sealing fire-rated non-combustible service penetrations and construction joints in horizontal and vertical fire separations. Single component silicone fire barrier for sealing around piping and wiring penetrations through fire-rated walls and floors. U.L. Listed; meets ASTM Specifications E-814, UL1479 and UL2079. Service Temperature Range: -51C to 149C (-51F to 300F). Application Temperature Range: -29 C to 50C (-20F to 122F).
NS Series- No slumping of vertical joints, gravity will hold positioning. Ready to use with a standard or bulk caulking gun or pneumatic pumping equipment. Cures in 20-40 minutes. Used to firestop openings and penetrations on fire rated floor stabs, walls, other building partitions and assemblies. Helps control the spread of fire, smoke and noxious gases. Meets ASTM Specification C920, Type S, Grade P, Class 25.
Provides up to 4-hour protection in tested and listed systems. Penetrates through fire-rated construction assemblies. Dries to red color, no mixing required. Helps prevent the spread of fire, smoke and noxious gas. Acts as an acoustic barrier by minimizing noise transfer. Helps create a smoke seal for systems requiring the optional L-Rating. Meets the intent of LEED VOC environmental regulations, international building code and other key life safety building code requirements.
Used to seal service penetrations and joints in fire separations and firewalls. Stops flame, smoke, and fumes under actual fire conditions. Easy to apply and cleanup, contains NO asbestos, paintable after cure. Nonflammable, provides a fireproof acoustic seal. GREENGUARD approved, meets LEED requirements.