With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies.

With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies.

With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies.

Made of a durable polycarbonate material that is virtually indestructible. 1/2" knockout. 4.3" length x 2.38" width. UL Listed.

Made of a durable polycarbonate material that is virtually indestructible. 4.3" x 2.38". UL Listed.

Made of a durable polycarbonate material that is virtually indestructible. 4.3 length x 2.38 width. UL Listed.

Rugged construction, used to close an outlet box. 4" square. Angled mounting slots allow for correction of box misalignment. UPC bar code. UL Listed.

Steel box cover, blank with no knockouts. 2-5/16" wide x 4-3/16" tall. UL Listed.

Steel box cover with single toggle switch opening in the center. 2-5/16" wide x 4-3/16" tall. UL Listed.

Steel box cover for duplex receptacle. Rugged construction. 2-5/16" wide x 4-3/16" tall. UL Listed.

Made of a durable polycarbonate material that is virtually indestructible. 4.3" length x 2.38" width. UL Listed.

Rugged construction, used to close an outlet box. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed.

Lightweight design and durable plastic. Listed for masonry walls. Safe to install and will never rust or corrode. Includes nails for quick, easy installation. 22 cubic inch rigid wall. 3-7/8" x 2-3/8" x 3-3/4". UL Listed.

Use two to mount switch box with plaster ears to hollow wall. Slips between box and wall, tabs bend inside box.

Used for convenience outlets, switch boxes or small junction boxes. Drawn construction and raised grounding provision. Acceptable for use in 2-hour rated walls. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Two 1/2" knockouts (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed.

Old work wall case. Safe, non-conductive. Two Zip-Mount retainers. Four integral clamps, two each end; mounting ears. 14 cubic inch,  2-3/4" x 2-1/4" x 4-1/8". UL Listed.

New work safe, non-conductive. With captive nails. Eight integral clamps, four each side. 32 cubic inches. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. 3" depth x 4" x 3-3/4".

PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. Includes hardware for quick, easy installation.

With captive nails. 3/0 - 4/0 combination. Fixture spacing for 2-3/4" - 3", 6 integral clamps. 4" diameter non-metallic ceiling box, 20 cubic inch volume. Listed for fixture support up to 50 lb. 4" diameter x 2-1/4" depth. Meets NEMA OS-2, UL Listed. RoHS Compliance.

Steel box cover with single 1/2" knockout in the center. 4" square. Angled mounting slots allow for correction of box misalignment. UL Listed.

Steel box cover with single 1.406" receptacle opening in the center. Rugged construction. 2-5/16" wide x 4-3/16" tall. UL Listed.

Steel box cover with 1/2" knockout in the center. 2-5/16" wide x 4-3/16" tall. UL Listed.

Steel box cover with single 1/2" knockout in the center. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed.

Conduit wiring system. Installed in ceilings or walls for lighting fixtures, switches or receptacles. Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for surface mount applications in ceilings or walls for lighting fixtures or receptacles. Eight 1/2"and four 3/4" conduit knockouts (sides). Two 1/2" and two 3/4" conduit knockouts (bottom). 4" square x 1-1/2" deep - 21.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. UPC bar code.

Steel box cover with 1/2" knockout in the center. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed.

Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed.

Suitable for tile, plaster, sheetrock, paneling, masonry and all wall coverings. Brilliant electric blue. UL Listed.

High impact lightweight round blank PVC cover for 4" round boxes to make junctions. UL Listed.

Two 1/2" and two 3/4" conduit knockouts (sides). Two 1/2" and two 3/4" conduit knockouts (bottom). No bracket. Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code.

Extends an existing box by 1-1/8". Used to correct problems from remodeling where the wall surface is extended. Fits between the wiring device and the wall surface. Extends the switch or outlet box to flush with the wall. Works with all standard wiring devices. 2-1/4" x 3-1/4". UL Listed.