Re-designed versatile hex shank drive shaft attached directly into the chuck of virtually any drill or 1/4" quick release chuck impact driver. Offset design saves hands. Navigates tight patterns and square cuts. Cuts a variety of building materials. 20 gauge capacity in galvanized steel. Use TS1RB TurboShear replacement blades.
Cuts up to 18 gauge material including, but not limited to sheet metal, corrugated sheet metal, duct, asphalt shingles, steel mesh, vinyl siding, wire, plastics, cardboard and rubber. 360 degree swivel head allows for maneuverability when cutting. Works with most 18 to 20 VAC impact driver and drill tool brands. 1/4" hex shank. Yellow/black color.
The telescoping drill clamp fits drill and impact drivers large and small, including newer Lithium-Ion models. It also allows the tool to rotate 360? and lock into position. The adjustment wrench stores with the tool, preventing loss. The hex shank drive shaft attaches directly into the chuck of any drill or impact driver. The TSHD navigates tight patterns and square cuts while cutting a variety of building materials. 18 gauge capacity in galvanized steel. Long-life, dual ball bearings. Use Replacement Blades TSHDRB.
Make your drill a double-cut metal shear. Now you can get double-cut performance in a versatile Malco TurboShear. Fits the corded or cordless drill you already own. A compact telescoping clamp accommodates both length and width of any size motor housing, including smaller impact drivers, to ensure easy one-hand operation. Optional spacers are stored on clamp for large motor housings. The clamp collar allows the shear head to be rotated 360? and set in any position for optimum tool clearance. The blades of Malco Double-Cut TurboShears remove a narrow spiral scrap from the tool path to produce a clean, straight edge on both sides of the cut. These blades can approach a cut from either end to produce a quality work-piece edge. They can also navigate up to 90? outside profiles of metal roofing panels, or metal ductwork, and are beefy enough to cut through seams. You can easily disengage the blades from the cutting path or quickly re-engage to continue cutting. The long lasting carbon steel blades are also easily replaced on the job.
This versatile and portable TurboShear fits a drill you already own to make easy cross cuts, fast lengthwise cuts and precise circular and square outlet cuts in large or small pattern corrugated metal roofing and common trapezoidal (box) pattern metal roofing panels. Elongated blades with compact jaws create a steep 75 degree offset so that the drill is held at a nearly vertical approach when starting a cut. As these offset blades follow the rising angle of a corrugated or trapezoidal profile, the drill handle or battery pack has clearance to naturally tip downward and still clear the roofing panel surface. A sleek, lightweight aluminum-cast shear head and compact molded polymer drill clam allow maximum portability and ease to go wherever the work is. The telescoping drill clamp adjusts to fit both length and width of popular drill sizes including smaller bodied Impact drivers. Optional spaces are stored on clamp for large motor housings. The clamp collar allows the shear head to be rotated 360? and set in any position for optimum tool clearance when navigating profiles or to facilitate easy material flow. The shear can operate at high or low speeds for the control you need to follow a precise life in 30 to 24 gauge (0.31-0.61mm) roofing panel metal. A lateral blade adjustment capability ensures that optimum cutting performance and maneuverability can be maintained for the life of the blades.
The telescoping drill clamp fits drills and impact drivers large and small, including newer Lithium-Ion models. It also allows the tool to rotate 360? and lock in position. The adjustment wrench stores with the tool preventing loss. The hex shank drive shaft attaches directly into the chuck of any drill or impact driver. Fast cutting blades are specialized for fiber cement siding only. The blade design minimizes dust. Wide skid plate design stabilizes for a precise clean cut, (including window and door arches) in fiber cement siding up to 5/16" (8mm). Replacement blade TSF1RB.