Forged carbon steel for maximum strength. Spring steel snap rings. Zinc plated to resist rust.

Forged carbon steel for maximum strength. Spring steel snap rings. Zinc plated to resist rust.

Forged carbon steel for maximum strength. Spring steel snap rings. Zinc plated to resist rust.

National Hardware Lap Link, Series: 3152BC, 3/16 in, Steel, Zinc Plated, 225 lb Load Capacity, Bolt Fastener, For Joining Two Lengths of Chain Together or Accessories to a Chain

National Hardware Lap Link, Series: 3152BC, 1/8 in, Steel, Zinc Plated, 120 lb Load Capacity, Bolt Fastener, For Joining Two Lengths of Chain Together or Accessories to a Chain

Forged steel, hot dipped, galvanized. Open-throat design, wide bow, screw pin shackle requires no tools to assemble. Slip screwdriver blade or hand punch through pin/eye and tighten. Meets Federal Specification RR-C-271F, type IV, Class 2.  WARNING: Inspect regularly. Replace if worn, distorted or damaged. Ensure pin is fully engaged. Seize pin with wire. Do not exceed WLL [Work Load Limit].Use only Duty Rated Shackles, with embossed WLL,for overhead lifting.

Campbell Welded Ring, 1 in Length X 0.18 in Wire Size, Steel, Nickel Plated, 200 lb Load Capacity

Factory number indicated thickness (inches).

For connections of chain and attachments (Not for overhead lifting). WARNING: DO NOT exceed working load limit.

Designed as a temporary chain link repair, use one size bigger than chain. Can be used to couple chain attachments. Do not reuse after closure. Manufactured from steel.

Forged carbon steel for maximum strength. Spring steel snap rings. Zinc plated to resist rust.

Forged steel, hot dipped, galvanized. Open-throat design, wide bow, screw pin shackle requires no tools to assemble. Slip screwdriver blade or hand punch through pin/eye and tighten. Meets Federal Specification RR-C-271F, type IV, Class 2.  WARNING: Inspect regularly. Replace if worn, distorted or damaged. Ensure pin is fully engaged. Seize pin with wire. Do not exceed WLL [Work Load Limit].Use only Duty Rated Shackles, with embossed WLL,for overhead lifting.

Connections for chain and attachments. When using cold shuts with chain, use one size larger than chain size. With a hammer, drive the open end through the cold shut eye then peen the extended end to prevent opening. Note: Cold shuts should not be reused after closure has been made. Do not use for overhead lifting.

National Hardware Cold Shut, Series: 3153BC, 1/4 in, 0.24 in Rod Diameter, 0.26 in Hole Diameter, Steel, Zinc Plated, 1250 lb Load Capacity, 1.61 in Width, For Use to Couple Chain Attachments

Connections for chain and attachments. When using cold shuts with chain, use one size larger than chain size. With a hammer, drive the open end through the cold shut eye then peen the extended end to prevent opening. Note: Cold shuts should not be reused after closure has been made. Do not use for overhead lifting.

National Hardware Lap Link, Series: 3152BC, 1/4 in, Steel, Zinc Plated, 500 lb Load Capacity, Bolt Fastener, For Joining Two Lengths of Chain Together or Accessories to a Chain

WARNING: DO NOT EXCEED the working load limit. DO NOT USE for overhead lifting, to support human weight, for playground or athletic equipment, or as safety device.

Forged carbon steel for maximum strength. Spring steel snap rings. Zinc plated to resist rust.

Campbell Welded Ring, NO 7 Chain, 1-1/4 in Length X 0.18 in Wire Size, Steel, Nickel Plated, 200 lb Load Capacity

National Hardware Ring, Series: 3155BC, NO 7 X 1 in, Steel, Zinc Plated, 195 lb Load Capacity, For Rope, Chain and Strap

.

National Hardware Cold Shut, Series: 3153BC, 5/16 in, 0.32 in Rod Diameter, 0.35 in Hole Diameter, Steel, Zinc Plated, 1900 lb Load Capacity, 1.94 in Width, For Use to Couple Chain Attachments

Meets requirements of Federal Specification RR-C-271D Amendment 1. Shackle pins are forged from alloy steel, heat treated and tempered to give greater strength. Galvanized per ASTM A153. Design factor 5:1

Forged steel, hot dipped, galvanized. Open-throat design, wide bow, screw pin shackle requires no tools to assemble. Slip screwdriver blade or hand punch through pin/eye and tighten. Meets Federal Specification RR-C-271F, type IV, Class 2.  WARNING: Inspect regularly. Replace if worn, distorted or damaged. Ensure pin is fully engaged. Seize pin with wire. Do not exceed WLL [Work Load Limit].Use only Duty Rated Shackles, with embossed WLL,for overhead lifting.

Baron Spring Snap, Open Eye, 9/32 in Snap Opening, 3-3/8 in Overall Length, Steel, Nickel Plated

Campbell Welded Ring, NO 4 Chain, 1-1/4 in Length X 0.22 in Wire Size, Steel, Zinc Plated, 200 lb Load Capacity

National Hardware Ring, Series: 3155BC, NO 4 X 1-1/4 in, Steel, Zinc Plated, 270 lb Load Capacity, For Rope, Chain and Strap

National Hardware Ring, Series: 3155BC, NO 3 X 1-1/2 in, Steel, Zinc Plated, 300 lb Load Capacity, For Rope, Chain and Strap

National Hardware Ring, Series: 3155BC, NO 7 X 1 in, Steel, Brass, 195 lb Load Capacity, For Rope, Chain and Strap

Campbell Welded Ring, NO 3 Chain, 2 in Length X 0.24 in Wire Size, Steel, Nickel Plated, 200 lb Load Capacity